Pilot Screw Adjustment for the Recon 250 ('97 and up)
This may also be suitable information for the same year 250SX quad.
Note:
-The pilot screw is factory pre-set. Adjustment is not necessary unless the carburetor is overhauled or new pilot screws are installed.
-The engine must be warm for accurate adjustment. Ten minutes of stop-and-go riding is sufficient.
-Use a tachometer with gradations of 50 rpm or smaller that will accurately indicate 50 rpm change.
1. Turn the pilot screw clockwise until it seats lightly, then back it out to the specification given.
CAUTION: Damage to the pilot screw seat will occur if the pilot screw is tightened against the seat.
TOOL:
Pilot screw wrench 07908-4220201
INITIAL OPENING:
'97 (except California type): 2 7/8 turns out
'97 CA type: 2 3/4 turns out
'98 - 2001: 2 5/8 turns out
After 2001: 2 turns out
2. Warm the engine up to operating temp.
3. Stop the engine and connect a tachometer according to the tach. manufacturer's instructions.
4. Start the engine and adjust the idle speed with the throttle stop screw.
IDLE SPEED: 1,400 +/- 100 rpm
5. Turn the pilot screw in or out slowly to obtain the highest engine speed.
6. Readjust the idle speed with the throttle stop screw
7. Turn the pilot screw in gradually until the engine speed drops 100 rpm.
8. Turn the pilot screw counterclockwise the number of specified turns.
FINAL OPENING:
'97 (except CA type) 3/4 turn out
'97 CA type/'98-2001: 7/8 turn out
After 2001: 1/2 turn out
9. Readjust the idle speed with the throttle stop screw.
For those who do not know, the throttle stop screw is on the right side of the carb. right behind the mounting stud where the carb. attaches to the intake rubber.
The pilot screw is on the front center underneath side close to the engine cylinder.
The above info. was taken from Honda's '97-'04 Recon service manual, and I hope this helps many. Print it out, and get it covered with your greasy fingerprints, and then throw it away!
I do not have a tach or a pilot screw wrench, but I do have ears and a screwdriver. I used these baseline settings to dial my wife's bike in perfectly. You can too.
This may also be suitable information for the same year 250SX quad.
Note:
-The pilot screw is factory pre-set. Adjustment is not necessary unless the carburetor is overhauled or new pilot screws are installed.
-The engine must be warm for accurate adjustment. Ten minutes of stop-and-go riding is sufficient.
-Use a tachometer with gradations of 50 rpm or smaller that will accurately indicate 50 rpm change.
1. Turn the pilot screw clockwise until it seats lightly, then back it out to the specification given.
CAUTION: Damage to the pilot screw seat will occur if the pilot screw is tightened against the seat.
TOOL:
Pilot screw wrench 07908-4220201
INITIAL OPENING:
'97 (except California type): 2 7/8 turns out
'97 CA type: 2 3/4 turns out
'98 - 2001: 2 5/8 turns out
After 2001: 2 turns out
2. Warm the engine up to operating temp.
3. Stop the engine and connect a tachometer according to the tach. manufacturer's instructions.
4. Start the engine and adjust the idle speed with the throttle stop screw.
IDLE SPEED: 1,400 +/- 100 rpm
5. Turn the pilot screw in or out slowly to obtain the highest engine speed.
6. Readjust the idle speed with the throttle stop screw
7. Turn the pilot screw in gradually until the engine speed drops 100 rpm.
8. Turn the pilot screw counterclockwise the number of specified turns.
FINAL OPENING:
'97 (except CA type) 3/4 turn out
'97 CA type/'98-2001: 7/8 turn out
After 2001: 1/2 turn out
9. Readjust the idle speed with the throttle stop screw.
For those who do not know, the throttle stop screw is on the right side of the carb. right behind the mounting stud where the carb. attaches to the intake rubber.
The pilot screw is on the front center underneath side close to the engine cylinder.
The above info. was taken from Honda's '97-'04 Recon service manual, and I hope this helps many. Print it out, and get it covered with your greasy fingerprints, and then throw it away!
I do not have a tach or a pilot screw wrench, but I do have ears and a screwdriver. I used these baseline settings to dial my wife's bike in perfectly. You can too.
Lectron is celebrating 45 years of helping riders get the most from their vehicles with our high performance carburetors and EFI. Thanks for your support!
Honda 400ex Carburetor Float Adjustment 1984 Evinrude 115 Hp
- I took the carb off just to see what changes were made. Here's what I have, White bro's E series slip on, #155 keihin main jet, #42 keihin pilot jet, stock needle jet (3rd groove down), pilot screw 3 turns out, (3) 1-1/2' holes in air-box, K&N filter with pre-filter.
- Rumble Please Check out my Sponsor Village Tactical And Absolute Computers http://www.absolutecom.